Payment & Shipping Terms:
|Size:||480x450x320cm||Color:||Customization Is Acceptable|
|Production Time:||10-15 Working Days After 50% Deposit Received||Warranty Period:||1 Year|
kids plastic jungle gym,
plastic outdoor toys
All plastic with 1.5 meter height slide and barriers outdoor playground for small venue with unusual colors TQ-QS008
We all know that children's play equipment will have different degrees of wear after using for a period of time. This kind of wear will affect the second-hand sales of equipment, and some even can not be used normally, there is a huge danger. So how do we deal with wear and tear? Below, we introduce you.
(1) Pre-wear period of amusement equipment
First of all, the new amusement equipment wears out very quickly when it is used, and as the running-in progresses, the rough appearance will be smoothed. At this time, the wear speed is reduced, and the running-in period ends. This period of time is called the pre-wear period.
At this time, the operator will consciously use the minute wear during this period to create conditions for the stable operation of normal operation. During this period, regarding the non-running equipment, the principles of load shedding, deceleration, and reasonable operation should be abide by, and the smooth oil with low viscosity should be added as much as possible. In addition, in order to shorten the running-in period, it is possible to select the appropriate leading technology, etc., and use the lubricating oil that meets the quality requirements to improve the utilization rate of the equipment.
(2) During the stable running-in period of the amusement equipment
During this period of normal operation, after the amusement equipment is run-in, the conflicting surface is hardened and the wear is slow and stable. In the later period of this period, due to metal fatigue, the wear is relatively accelerated, but it still works continuously. When approaching the fatigue limit of metal, the operator must perform regular forced repairs on the equipment to prevent the equipment from causing major accidents due to excessive wear. .
(3) During the intense wear of amusement equipment
During this period, because the metal outer surface of the amusement equipment reached the fatigue limit at all, the conflict conditions were greatly changed (such as a sharp rise in temperature, a significant change in the surface metal arrangement, a slight change in the shape of the microscopic, an increase in the gap, a deterioration in the smooth condition, etc.) ), the wear rate of the equipment is sharply increased, the mechanical efficiency is reduced, the precision is lost, abnormal noise and vibration occur, and the mechanical properties of the data are changed, eventually causing the parts to fail and must be repaired. At this time, if it is forced to operate normally or even at a high load, a major accident will inevitably occur.
So, what is the correct way to find out that children's play equipment is worn out?
1. Lubrication. If the wearing parts of the amusement equipment are lubricated, the friction generated between the parts can be reduced, and the wear can be reduced;
2. If there is an error in the installation position of the children's play equipment, wear will occur. Therefore, we remind operators to increase the accuracy of the installation in order to reduce wear and often check.
3. Finally, there is a point that some dust can easily cause wear and tear in children's play equipment, and some can cause rust and cause more problems. Therefore, it is also very important to keep the amusement equipment clean.
|Safety Area (mm)||780*750cm(L*W)|
|Modules||Roofs, slides, plastic panels, stairs, decks, tubes and posts, climbing.|
|Material||A. Plastic parts: Imported LLDPE|
|B. Post: National standard galvanized steel pipe|
|C. Metals: Galvanized|
|D. Deck, stair, bridge: Steel with plastic covered|
|E. Fasteners: 304 stainless|
|(Different material is available at your demand. )|
|e.Color is not easy to fade|
|Installation||2 day (2 persons)|
|Falling Height (mm)||2200|
|Age Range||3--12 age|
|Apply to||Amusement park, kindergarten, preschool, residential area.|
|Packing||Standard export packing|
|Plastic parts: Bubble bag and pp film;|
|Iron parts: Cotton and pp film|
|Use Life||7-10 years|
|Remark||1.Please check the screws and other catchers regularly to assure the firm structure.|
|2.Please make sure that all the kids play with adult supervision.|
|3.Blunt objects and acid corrosive liquor are forbidden.|
Contact Person: Lisa